Hand cream tube  manufacturers describe common problems in the application of tubes

(1) The tube is damaged. The hand cream tube manufacturer tells you to hook iron wire on some damaged edges. If the rusted tube is damaged, separate the rubber and plastic product layer from the outside for routine physical examination. The data shows that hooking iron wire on some damaged edges , rusted. This is mainly because the compressive strength of the tube is weakened due to the harm of moisture in the body or the corrosive organic compounds in the air, and it is damaged when the pressure is high. If this happens frequently, it will usually be accompanied by the breakage, scratches or significant mildew of the plastic rubber layer of the external structure, which will cause the surface layer to lose the safety protection hazard for upgrading. In response to this, the precondition is to inspect and remove all the bad reasons such as damage to the machinery and equipment of the external rubber and plastic product layer, chemical corrosion, high temperature manufacturing, etc., and then replace the rubber tube.

(2) The reinforcing layer of the tube failed to rust, but the reinforcing layer often had non-standard silk damage. The tube was damaged, the external structural adhesive was separated, and the reinforcement layer failed to rust, but it was broken non-standardly along the specification perspective of the reinforcement layer, mainly because the tube was damaged by high-frequency impact force. There are many intersection points between the stainless steel wire and the stainless steel wire of the hand-woven reinforcement layer. If the working pressure in the pipeline changes greatly, along with the change of the diameter of the pipeline, this intersection point will also move abnormally, and friction will occur in the middle of the transmission line.

The hand cream tube manufacturer tells you the common faults that occur in the split opening.

( 50ML-100ML Sunscreen Packaging PCR Recyclable Plastic )

(1) Hand cream tube or more tubes are cracked, the gaps are neat, and other positions remain stable. The hand cream tube manufacturer tells you that the key to this kind of situation is that the working pressure of the system software is too high, which exceeds the pressure resistance of the tube. If the working pressure of the system software complies with the regulations, it should be determined whether the actual pressure resistance level of the commonly used tubes can meet the requirements of the design scheme.

(2) The area where the tube is cracked will be twisted. The hand cream tube manufacturer tells you that this is due to the excessive twisting of the tube during the installation or application process. After the tube is twisted, the structure of the lifting layer changes, the spacing of the hand-woven fine iron wires increases, the compressive strength of the tube decreases, and the tube is very easy to crack under the action of high pressure. Therefore, in the process of using or storing the tube, please ensure that the tube does not carry torque, and when installing the tube, please try to place the shafts of the two connection numbers on the moving plan to ensure that the tube is in the process of fitness exercise. No frame drops.

(3) There is a stainless steel wire coiled on the cracked side of the tube, and there is a prominent head and neck folded condition near the crack. The factor for the loosening of the reinforcing layer is that the tube is subjected to excessive tensile deformation, and the layers are separated, and the compressive strength reduce. The hand cream tube manufacturer tells you that the tube is easy to stretch or stretch at a long and short angle under the effect of high pressure. Generally, the amount of stretching is 2% to 4% of the normal amount. When the tube is installed, the selection is too short, and the stretching effect is obtained during work. When it is more serious, common faults such as cracking or falling off will occur.

In general, through the in-depth analysis of the hand cream tube manufacturers, the following key points must be considered when using hydraulic tubes in the future:

The tube part should be placed as far as possible to prevent the thermal environment and solve the problem of starting the module out of the bronchus. Hand cream tube manufacturers tell you that if you want to use it, you can also use equipment such as maintenance tubes or protective screens to prevent the tube from deteriorating into heat.

When the tubes are to be overlapped or manipulated, safety devices such as tube clamps or compression springs should be applied on the surface of industrial equipment where sliding friction is likely to occur to avoid damage to the external structure of the tube.

When using a deformable tube, the bending radius should not be too small, and should exceed 9 times the diameter. The hand cream tube manufacturer tells you that the area where the tube and the socket are connected must have a vertical section that is 2 times larger than the diameter of the pipe.

The hand cream tube manufacturer tells you to prevent tension when installing the tube, even if there is no relative speed on both sides of the tube, you need to maintain the tube slack. Tight tubes swell under working pressure, reducing their compressive strength. Do not twist the tube during installation. Hand cream tube manufacturers suggest twisting the tube slightly, the compressive strength will be reduced, and the connector will be loose. When assembling, the tube should be tightened on the tube instead of the tube on the connector.

When the hand cream tube manufacturer tells you that the tube is equipped on key components, it is recommended to maintain or replace it regularly.